Browse all practice questions for the North Carolina Mechanical Code Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

North Carolina Mechanical Code Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • A fuel-fired furnace installed in a closet less than 12 times the total volume is only allowed if it is:
  • When referring to 4" diameter ducts, the numbers 6", 8", and 10" typically indicate what measurement?
  • How should the means for manually disconnecting the control circuit be accessible?
  • What is the maximum temperature limit set for sauna heaters?
  • Which type of appliance is critical for removing smoke and odors in commercial food services?
  • When deenergized, what should happen to the burner according to safety standards?
  • Forced draft systems and portions of induced draft systems must be designed to be __________ to prevent leakage of combustion products.
  • What is the maximum distance at which external duct insulation must be legibly identified?
  • What is the minimum height requirement for the top of a guard when adjacent to elevated surfaces?
  • System components must be protected from freezing at what ambient temperature?
  • What is the minimum distance a floor furnace should be from the nearest wall?
  • Who is responsible for the administration and enforcement of the mechanical code?
  • What should not be located on either side of a safety or relief valve connection?
  • What is the minimum air handling capacity that requires the installation of smoke detectors?
  • What is the required distance for vent terminations from an adjacent wall?
  • What type of equipment is mentioned that produces condensate and requires auxiliary protection methods?
  • What is the maximum permissible quantity of refrigerant in a residential unit system other than an exit access?
  • What diameter should the discharge pipe of safety and relief valves have?
  • Electrical wiring for regulated equipment must comply with which code?
  • Changing the occupancy of a structure without proper approval is deemed what?
  • Which type of cooking appliances does Medium-Duty include?
  • What is required for combustion air ducts that pass through walls without dampers?
  • Which appliances require a Type I hood when producing grease or smoke?
  • What material is specified for the minimum thickness of pans according to gauge?
  • What is the minimum size access opening required when installing HVAC equipment in an attic?
  • What is the required minimum horizontal clearance that vent terminals must maintain from doors?
  • What is the maximum length of a listed air duct connector?
  • Connecting ducts to non-dedicated vents is considered...
  • What must be ensured before the operation of refrigerant-containing systems erected on the premises?
  • What is the purpose of a power venting system?
  • Design plans for a commercial kitchen ventilation system must include what type of documentation?
  • What is the purpose of an interlock in a mechanical system?
  • Which component is crucial for the safe operation of a steam boiler?
  • How much of the floor area being ventilated must natural ventilation openings comprise at a minimum?
  • Electric kilns must comply with which testing standard?
  • What is the definition of equipment in the context of building systems?
  • What is defined as occupiable space?
  • What is the minimum indoor temperature that space-heating systems must maintain for human occupancy?
  • What interior finish is required for exhaust ducts?
  • What aspect must not change in minor alterations to existing mechanical systems?
  • Which type of appliances do not require a Type I hood if the grease content is 5 mg/m3 or less?
  • What type of damper should be included at the termination of a dryer exhaust duct?
  • Which component pumps water in an air washer system?
  • What labeling is required for access points to dampers?
  • How much higher must Type L vents extend above the highest point where they pass through the roof?
  • What is the maximum bore hole size permitted in wood studs for structural integrity?
  • What should trigger the automatic operation of mechanical ventilation systems in enclosed parking garages?
  • What information is required on labels for thermal storage units?
  • What is the minimum number of units horizontal for the slope in condensate piping?
  • What type of duct material is required for makeup air ducts?
  • In boiler installations, what is required in the supply and return piping?
  • Where should screens not be installed in relation to duct or weather cap terminations?
  • What must be done to existing ductwork when insulation is specified for installation of new cooling equipment?
  • In which areas should local exhaust systems be provided?
  • Where must any venting system for appliances terminate relative to each other?
  • Where should a fill pipe terminate in relation to a building opening?
  • What is the maximum size opening in a residential air intake screen which terminates outdoors?
  • How many shutoff valves must be installed on both sides of a pressure-reducing valve?
  • What characterizes a vent used for conveying combustion products?
  • According to the standards, the smoke-developed index for duct coverings must not exceed what value?
  • What is required for unconditioned basement ductwork with the addition of cooling?
  • What is the flow restriction for return air from any room according to the code?
  • Dryer exhaust ducts must terminate on the outside of the building and be equipped with what kind of device?
  • Which construction is NOT required for the space between the corridor ceiling and the floor above when used as a return air plenum?
  • What is the term used for the region within an occupied space that is located between 3 and 72 inches above the floor?
  • When should the makeup air system start in relation to the exhaust system?
  • What label is associated with rectangular ducts according to this code?
  • What defines a chimney in mechanical structures?
  • What is the purpose of doorstops and door closers in relation to vented wall furnaces?
  • Cooling towers are required to have what feature for safety?
  • To protect solar energy system components from vacuum conditions, which device should be used?
  • What type of joint creates a gas-tight seal through the melting of materials at high temperature?
  • What shape are connectors typically labeled as in duct systems?
  • Vented wall furnaces must be located such that a door cannot swing within how many inches of an air inlet or outlet?
  • Which system is needed to ensure proper smoke control in corridors?
  • Commercial electric water heaters are required to comply with which standard?
  • Mechanical or natural ventilation is required for any enclosed refrigeration system located outdoors and more than how many feet from building openings?
  • Where must liquid fuel vent pipes terminate in relation to buildings?
  • Which of the following rooms is a prohibited location for fuel-fired appliances?
  • Foam plastic used as duct coverings and linings must conform to the requirements of which section?
  • Bored holes not greater than 60 percent of the depth of the stud are permitted in what type of partitions?
  • How far downstream of a fuel burning duct heater must duct linings be removed?
  • Type I hoods must discharge to what type of exhaust system?
  • What type of joint involves a compression joint with a conical spread made on the end of a tube?
  • Polybutylene pipe and tubing must be installed in what type of lengths?
  • Which of the following is NOT a feature of occupiable space?
  • How far from operable openings into buildings should ducts conveying explosive or flammable vapors be positioned?
  • Which standard must supply tanks conform to for underground installations?
  • What is the minimum flash point for liquid adhesive coatings used on filters?
  • Which organization sets the standard for testing stationary fuel-cell power plants?
  • What is the role of the smoke damper in HVAC systems?
  • In the context of venting requirements, what is the purpose of a power exhauster?
  • Which type of remote control should be installed to manage fans in flammable environments?
  • Which characteristic of ducts is essential for preventing air leakage?
  • What is the minimum gauge for stainless steel used in Type I hoods?
  • Which document typically describes a construction project's design and physical characteristics?
  • Which type of joint is characterized as permanent or removable based on design?
  • What is prohibited from being installed on return piping?
  • What measurement indicates the acceptable minimum opening size for louvers?
  • Supply air to a swimming pool and associated dock areas shall not be recirculated unless such air is _____ to maintain the relative humidity of the area at ___ percent or _____.
  • Ducts shall not be located within how many inches of the earth?
  • According to the guidelines, transition ducts connecting the dryer should be of what construction standard?
  • What is the minimum depth required for the pan?
  • What aspect of water quality does the midpoint of the water-gauge glass indicate?
  • What must pressurized thermal storage units include according to the guidelines?
  • Who is responsible for identifying the location and installation of dampers in building plans?
  • To what minimum thickness must the underground duct system be encased?
  • Which refrigerant group does not require more stringent pipe specifications compared to Group A1?
  • What is the required timeline for submitting a permit application after emergency repairs or replacements?
  • What aspect does the Smoke-Developed Index evaluate in materials?
  • What is typically needed to ensure safe operation of mechanical equipment positioned on rooftops?
  • Which type of piping is approved for heating panels?
  • What type of heat recovery ventilators must be listed and labeled according to specific standards?
  • Which requirement is NOT associated with the installation of connectors in venting systems?
  • Incidental air movement is allowed from which type of rooms within health care facilities?
  • In a split-level home, how much total area can the levels served by one return be?
  • What feature must be included in duct installation to maintain proper airflow?
  • What type of system must be provided and operated in areas with irritating or health-hazardous contaminants?
  • What is the minimum distance required between the lowest edge of a grease filter and the cooking surface for appliances exposed to charcoal or charbroil?
  • For boilers with fuel input greater than 12,500,000 Btu/hr, which standard do the controls and safety devices need to meet?
  • What type of hood must be used for commercial cooking appliances to be exempt from certain venting requirements?
  • Power exhausters serving automatically fired appliances must be __________ to prevent operation when the power exhauster is not in operation.
  • What is the minimum dimension required for a crawl space support at each corner of the unit?
  • What is a potential risk if safety and relief valves discharge inappropriately?
  • When testing refrigerant systems, what is the minimum test pressure requirement?
  • What type of units must heating panels be unless otherwise labeled?
  • What must a fireplace door comply with if it's not specifically tested for factory-built fireplaces?
  • Factory-built chimneys shall be listed and labeled according to __________.
  • Mechanical ventilation of machine rooms is required; _________ may be used when the system is outdoors and located more than 20 feet from any structure or openings.
  • What is the minimum size of a return line required for fuel oil piping?
  • How must heating panels be installed in relation to framing members?
  • What is the maximum face velocity allowed for return air grilles in non-engineered systems?
  • Fireplaces are constructed following specific codes for what primary reason?
  • The minimum size of a supply line shall be ___-inch (9.5 mm) inside diameter nominal pipe.
  • What standard must domestic dryer exhaust duct power ventilators meet?
  • When a cooling coil is installed directly to a furnace, what must the drain pan be sized for?
  • The total area for ducts should not exceed what measurement for every 100 square feet of floor area?
  • What is required at the connection to each fuel-oil-burning appliance?
  • What type of duct label usually indicates the system's classification?
  • What is the requirement for the ceiling height in corridors to function as a return air plenum?
  • What must be provided for motors and fans to ensure they can be serviced safely?
  • What is the minimum required distance for exhaust outlets from exterior walls and roofs?
  • What material is specified for aluminum dryer ducts?
  • Connections for refrigerant piping between condensing units and riser boxes do not require enclosures if the connections do not exceed what length?
  • Which code covers natural gas and propane fired appliances?
  • Cleanouts in horizontal ducts should be installed on which side of the duct?
  • What is the maximum gauge increment for tests requiring pressure above 100 psi?
  • At which distance upstream and downstream must linings in ducts be interrupted relative to fire dampers?
  • Which of the following describes tubings such as semirigid conduits?
  • Pumps that are not part of an appliance shall be of a _____-_____ type.
  • For appliances in rooms, what is the minimum passageway height requirement?
  • What assembly technique is appropriate for creating a sturdy support for crawl spaces?
  • What must the ventilation system be in areas where explosive or flammable vapors, fumes, or dust are generated?
  • Factory-built equipment and appliances must be tested according to which standard?
  • What is the minimum fire resistance rating required for corridor dampers?
  • In what circumstance are smoke detectors exempt from the return air system?
  • What is the appropriate joining method for polyethylene pipes?
  • In a smoke control system, combination fire/smoke dampers should not be activated by what, unless secondary to the smoke management system controls?
  • What type of material should be used to seal the annular space where a clothes dryer exhaust duct penetrates a wall or ceiling?
  • Medium-heat appliances operate with combustion products at what temperature range?
  • What is considered a toilet room in mechanical code?
  • Does the addition of cooling equipment in a crawl space require existing ductwork to be insulated?
  • Why is a low water cutoff control needed in certain boilers?
  • What direction should pumps operate when providing fuel oil?
  • What is the diameter of the sphere that guards should prevent the passage of?
  • What is not required for coil type and water tube type boilers that have forced circulation of water?
  • What is the acceptable method for marking access points for smoke and fire dampers?
  • What device must dryer exhaust ducts for clothes dryers be equipped with?
  • What is a requirement on a grease hood that is used to catch grease?
  • What type of motors should be used in areas with flammable vapors or dust?
  • Openings in exhaust ducts shall be covered with corrosion-resistant screens of what minimum mesh size?
  • How are refrigeration systems classified?
  • What standard must fire dampers comply with?
  • What standard should domestic dryer exhaust duct power ventilators be listed and labeled to?
  • What is the exception condition under which elevation of the ignition source is not required?
  • What phrase refers to the ability to reach a device or equipment directly without removing any obstructions?
  • What is the key characteristic of a dwelling unit?
  • Which standard is not directly associated with electric heaters?
  • What is defined as an appliance under the mechanical code?
  • What is the minimum required separation in feet between outdoor air intake openings and any lot lines or buildings on the same lot?
  • How many shutoff valves are required for each boiler in multiple boiler installations?
  • The diameter of holes bored in joists should not exceed what fraction of the depth of the joist?
  • In what situation are shutoff valves not required in boiler systems?
  • What is the definition of the net occupiable floor area?
  • The maximum allowable amount of R-408A in a 2000 cubic-foot Institutional Occupancy is _____ lbs.
  • Exhaust outlets must terminate a minimum of how many feet from adjacent buildings and property lines?
  • Why must air transported through rock or dust-producing materials be filtered?
  • How should duct systems serving Type I hoods be designed to prevent grease accumulation?
  • Tanks must be covered with at least how many feet of earth for protection?
  • Oil-fired furnaces are required to be tested in accordance with which standard?
  • What classification of appliance has combustion products entering the flue at temperatures exceeding 1,000°F but not greater than 2,000°F?
  • What is an essential feature of cleanout openings for proper maintenance access?
  • Under what condition are shutoff valves not required in a low-pressure steam boiler system?
  • What is the maximum combustion product temperature for a low-heat appliance (residential appliance)?
  • What type of tubing must be installed in continuous lengths or joined through heat fusion?
  • Which of the following is a requirement for tanks larger than 10 gallons?
  • Nonmetallic ducts must be constructed with which class of duct material?
  • The minimum clearance to combustibles for a hydronic piping system is based on what factor?
  • In which type of walls is it permitted to cut or notch any wood stud, provided it does not exceed 25 percent of its depth?
  • What status should the controls have when the control circuit is de-energized?
  • How high must subslab soil exhaust system ducts terminate above the roof?
  • What is the minimum height above adjoining grade for other product conveying outlets?
  • Ducts are not allowed to be located within how many inches of the earth?
  • What is the minimum distance that environmental air exhaust must be from property lines?
  • What is a conditioned space?
  • What marking is used for pressure-sensitive tape in ductwork compliant with UL 181B?
  • Which authorities oversee the compliance and enforcement of mechanical code standards?
  • In what manner should liquid fuel vent pipes be installed in relation to fill pipes?
  • What is the purpose of an expansion tank in a hot water system?
  • In flood-prone areas, how should solar systems be positioned?
  • Hydronic piping and fittings can be made of which of the following materials?
  • Makeup air ducts must be constructed according to specific sections if they connect within what distance to a Type I hood?
  • How long must fuel storage rooms and boiler rooms be separated by in public schools?
  • How should pipe ends be prepared before installation?
  • What is the maximum length for listed air duct connectors?
  • When replacing heating or adding cooling equipment in certain basements, what is not required?
  • What do machinery rooms help protect building occupants from?
  • The total free area opening to provide makeup air must do which of the following?
  • What term describes air moved from one indoor space to another?
  • What is the maximum flame spread index allowed for duct coverings to reduce fire and smoke spread?
  • For tests requiring a pressure greater than 10 psi but less than or equal to 100 psi, what is the maximum gauge increment?
  • For appliances using forced draft venting, what is the required minimum clearance from vent terminals to combustion product openings?
  • What is the term for a semirigid conduit made of materials such as copper or plastic?
  • What type of gauges should not be used for oil tanks due to the risk of breakage?
  • What should be the nature of the supports for equipment concerning condensate drain pans?
  • What type of pipe seam requirement exists for piping located in flood hazard areas?
  • How must heating panels that are not labeled for field cutting be installed?
  • What is a requirement for the labeling of heat recovery ventilation systems?
  • Are undercut doors allowed for return air movement in non-engineered systems?
  • What must the exhaust for Type I hoods be designed to prevent?
  • What type of materials is the exception for minimum clearance applied to?
  • Recovered refrigerants may be reused if used back into the system it was _____ from.
  • In a closet designed for the installation of a clothes dryer, what should be the minimum opening size for makeup air?
  • Where should motors for fans conveying flammable vapors be located?
  • The air handling unit (AHU) for a corridor must be shut down by what in certain situations?
  • What is the requirement for external duct insulation that is not spray polyurethane foam?
  • Which type of venting systems has exceptions for minimum vent height regulations?
  • Transition ducts must remain entirely within which area?
  • Who is required to prescribe the location of appliances in hazardous areas?
  • What is the refrigerant number for Butane?
  • What device is recommended to prevent damage from condensate?
  • Where should cleanouts serving horizontal sections of grease ducts be located?
  • What device is designed to close automatically upon detection of heat and resist the passage of flame and smoke?
  • It is unlawful to change the occupancy of a structure without approval if it subjects the structure to what?
  • The operating temperature limit in a smoke control system shall not exceed which of the following?
  • A fuel-fired appliance must not obtain combustion air from which of the following locations?
  • In a dwelling unit, the use of corridors for conveying return air is:
  • When rubber cement is used or mixed, what must be ensured about the room's ventilation?
  • Which of the following materials is specifically mentioned for construction when discussing brick supports?
  • What defines self-contained equipment in heating, air-conditioning, or refrigeration?
  • What status must mechanical systems maintain to be compliant when inspected?
  • What must not be done to pipe ends when preparing them?
  • What must ensure that excessive pressures do not lead to isolation in a solar energy system?
  • What is the minimum gauge steel required for the construction of Type I hoods?
  • Chimneys for open combustion chamber appliances in buildings other than dwelling units must be marked "__________".
  • What is the relationship between altitude and the fuel input rate of appliances?
  • Metallic underground ducts without an approved protective coating must be encased in a minimum of how many inches of concrete?
  • A fan interlock is required to prevent heater operation when what condition is not met?
  • In the event of a conflict between a general requirement and a specific requirement, which requirement shall govern?
  • When is a Type I hood not required for an appliance?
  • What is the recommended action for a ventilation air intake that is too close to a property line?
  • Permanently installed equipment powered by internal combustion engines must be installed according to which standard?
  • The fuel oil system shall be sized for the _____ capacity of fuel oil required.
  • Automatic dampers for oil-fired heating appliances must comply with which standard?
  • What types of fuel does the mechanical code apply to?
  • What type of makeup air systems must be equipped with closure means?
  • In which type of space are ducts not required to be sealed?
  • Type I hoods are mandatory over which categories of cooking appliances?
  • What gauge of galvanized steel is specified for clothes dryer ducts?
  • What must be provided where appliances and other components requiring service are located within 6 feet of a roof edge?
  • What must cleanouts be provided with to allow cleaning and inspection of the duct?
  • Before converting an appliance to a different fuel type, what must be secured?
  • Who bears the responsibility for discrepancies between code provisions and equipment installation instructions?
  • Which type of air must be filtered according to general requirements for filters?
  • What is the minimum distance that outside above-ground tanks must be from an adjoining property line?
  • What distance should a floor furnace be placed from the nearest wall, except for wall register models?
  • What is a key measure to mitigate risk in machinery rooms related to refrigerants?
  • What type of cap or fitting should vent pipes terminate with?
  • What is the minimum gauge steel required for Type I materials in construction?
  • The provisions relating to historic buildings are what?
  • What is the minimum distance that ducts must be installed above the earth?
  • What type of venting appliances must maintain a clearance of at least 12 inches?
  • High pressure-steam safety valves should be vented in which direction?
  • What type of device should pressure vessels be equipped with according to installation instructions?
  • Under what condition can appliances be located in hazardous locations?
  • Which type of appliances are listed and labeled for venting with Type L vents?
  • According to the code, what type of approval is necessary for alterations to truss components?
  • Where should shutoff valves be installed concerning a heat exchanger?
  • What does "181B-M" denote in terms of closure systems?
  • What standards must thermal solar water heaters comply with?
  • What is the minimum height that a unit must be supported above grade?
  • From which part of a building is the return air not allowed to be taken?
  • What device is needed to protect solar energy system components against excessive pressures and temperatures?
  • What is the minimum distance required between the lowest edge of a grease filter and a cooking surface with exposed flame?
  • What is typically included as part of an air dispersion system?
  • What is prohibited in the joints of dryer exhaust ducts?
  • What is a common characteristic of the dust, stock, and refuse systems prohibited from having energy recovery ventilation?
  • Dryer exhaust systems must be independent of all other systems and convey moisture and combustion products to which part of the building?
  • What is NOT permitted in a corridor when used for returning air?
  • What should not be taken from a location defined as a hazardous space?
  • What is the required minimum clearance from a vent termination to a building structure?
  • What does the rule of thumb for "exposed within the space" refer to?
  • Which of the following cannot serve as supply, return, exhaust, relief, or ventilation air ducts?
  • Mechanical joints should not be used on annealed temper copper tube larger than what size?
  • What is the minimum clearance required on the control side of an excavation for floor furnace clearances?
  • What type of cover is required for fill openings?
  • What classification type is given to systems with potential for low refrigerant leakage into occupied areas?
  • What is the minimum height for letters on a warning notice according to sauna heater regulations?
  • What must clothes dryer exhaust ducts be constructed from according to the mechanical code?
  • What height should the inlet to an exhaust system be located regarding contaminant concentration?
  • What is prohibited from being installed at the termination of factory-built chimneys?
  • Where should fire and smoke dampers be located?
  • What triggers the requirement for more rigorous design standards in refrigerant systems?
  • What kind of vapors or fumes does NCMC 514.2 prohibit energy recovery ventilation systems from being installed in?
  • What type of signal should duct smoke detectors report to a supervising station?
  • In which type of exhaust systems are energy recovery ventilation systems prohibited from being installed?
  • What is the ideal design approach for clothes dryer installations regarding exhaust?
  • Solid fuel furnaces are required to be tested in accordance with which standard?
  • What is the maximum size of annealed temper copper tube allowed in refrigerant lines?
  • In which type of connectors are manual dampers allowed?
  • What is the minimum height a combustion air intake opening must be located above contaminant sources?
  • What is the maximum design air temperature for flexible air ducts and connectors?
  • How does the amount of return air taken from a room relate to the flow rate of supply air?
  • What must be done to nonfactory tested, field erected equipment according to regulations?
  • Which is a necessary element for proper below grade installation?
  • What type of valve must be installed ahead of the controls in vented wall furnaces?
  • At maximum, how far apart should straps be placed when supporting ducts?
  • Design plans for commercial kitchen ventilation systems must indicate what?
  • Which type of duct tape is prohibited as a sealant on metal ducts?
  • According to the International Energy Conservation Code, hydronic piping must be insulated to what requirement?
  • Which label is used to identify fire and smoke dampers on building plans?
  • The acronym ASSE stands for which of the following?
  • What method of transport should be avoided for air going into occupied spaces?
  • Where should the controlling thermostat for a floor furnace be located?
  • What is required for the cross connection of supply tanks not exceeding 660 gallons?
  • When must the makeup air system start to operate in relation to the exhaust system?
  • Which code specifies installations related to the protection of potable water systems?
  • How are duct connections typically sealed in HVAC systems?
  • How high must an electric hot water heater be elevated in a private garage to ensure safety?
  • What type of joint employs heat to fuse thermoplastic piping materials together?
  • What is the required minimum distance a vent system must terminate from any door, window, or air inlet into the building?
  • Which standard must be met by solid-fuel-fired ovens?
  • What is necessary for the underground duct system before it is coated or placed in the ground?
  • Who is responsible for the maintenance of mechanical systems?
  • What is the maximum size for openings in screens, louvers, and grilles?
  • Which division is responsible for the standards regarding pressure vessels?
  • Which of the following is NOT an acceptable location for condensate discharge?
  • What provides a standard for closure systems to seal flexible air ducts according to UL 181B?
  • In an equipment room, fusible plugs must terminate outside the structure at least how many feet above the adjoining grade?
  • What should the height of letters on damper access labels be at a minimum?
  • Where is it prohibited for condensate to discharge?
  • Electric infrared radiant heaters must comply with which standard?
  • Return air openings must be at least how many feet away from an open combustion chamber?
  • What is the purpose of a vent connector in a fuel-fired appliance setup?
  • According to standard codes, oil-fired appliances should be installed in compliance with which document?
  • What is required for the operation of fans in systems with flammable vapors?
  • Which of the following best describes a "boiler"?
  • What type of control is preferred for makeup air systems?
  • The standard for the testing of factory-built fireplaces is identified by which code?
  • What is the minimum slope required for horizontal grease ducts longer than 75 feet?
  • What type of signal must duct smoke detectors report as in monitored facilities?
  • Which of the following systems are not required to be classified as a high probability system?
  • Which type of liquid or gas must not be used as a heat transfer fluid?
  • Non-factory tested, field erected equipment and appliances must be pressure tested in accordance with which section?
  • For what purpose can space be used as part of an engineered smoke control system?
  • Exceptions for chimneys used with __________ chamber fireplaces require compliance with UL 103 regulations.
  • Which standard must metal chimneys meet during construction and installation?
  • What is the minimum ventilation airflow rate required per square foot of floor area?
  • A duct made from gypsum boards is typically used for which type of air system?
  • What is the maximum amount of fuel oil that can be stored in an above-ground tank for 1-2 family dwellings?
  • What is the purpose of the cross-sectional area in an areaway related to duct termination?
  • How should dampers be indicated on the building design plans?
  • Fuel-gas devices used with refrigeration systems shall be installed per _____ _____ _____ code.
  • What must be provided to solar energy equipment and appliances for maintenance?
  • Which of the following shall not serve as supply, return, exhaust, relief, or ventilation air ducts?
  • What is one of the requirements for cooking appliances in commercial settings?
  • Embeddment for buried system portions must be __________.
  • What is the purpose of smoke dampers in relation to combustion air openings?
  • What is the purpose of the design flood elevation in relation to tank installation?
  • Where shall supply piping connect to a fuel oil tank?
  • What is the minimum required air velocity within grease ducts serving Type I hoods?
  • What is the design capacity in cfm that necessitates installing smoke detectors in return air risers?
  • The embedded joints of piping in a building must be compliant with what joining method for copper?
  • What is the purpose of the discharge line connected to a relief valve?
  • What type of venting system utilizes mechanical means to remove flue or vent gases?
  • A grease reservoir with a cleanout must be provided at the base of each:
  • For connectors meant for two or more appliances, which connector should enter at the highest level?
  • In how many instances can doubled studs be bored per adjacent unit?
  • What is the required minimum slope for horizontal ducts exceeding 75 feet in length?
  • What must not be exceeded when adjusting the fuel input rate of an appliance?
  • In which locations are floor furnaces prohibited from being installed?
  • The bottom of a grease duct reservoir must slope towards what?
  • What term is used for a device or material that has been evaluated and affixed with a label by a recognized testing agency?
  • Mechanical equipment exposed to wind must be designed according to which code?
  • In duct installation, what is the specification for duct openings leading into the garage?
  • What standard must pipe insulation be tested in accordance with?
  • Holes bored in joists should not be within what distance from the top or bottom of the joist?
  • What is the minimum clearance required on the control side of a floor furnace?
  • What type of system can be used for transferring fuel oil?
  • What is the minimum clearance required for commercial clothes dryer exhaust ducts relative to combustible materials?
  • Which type of drain should be connected to the drain pan provided with equipment?
  • What material must the sauna room warning notice be constructed from?
  • In certain occupancies, a duct that penetrates a fire-resistance rated floor/ceiling assembly may connect how many stories without requiring shaft enclosure protection?
  • Outdoor air requirements may be designed by which type of professional?
  • What type of systems should gypsum boards not be used in?
  • What type of appliances must be used for domestic cooking operations?
  • What kind of detection should an auxiliary drain pan include?
  • Which standard must nonmetallic fasteners comply with for duct installation?
  • What type of assembly should flexible ducts and air connectors not pass through?
  • The hearth extension must be distinguishable from the __________.
  • Which kitchen hood is specifically designed for removing grease vapors and smoke?
  • What is the minimum required slope for grease hood exhaust ducts?
  • What type of control does a clearly identified break-glass switch provide for ventilation systems?
  • What type of ducts are prohibited in clothes dryer installations, except for the transition duct?
  • What is defined as a rigid conduit made of materials like iron, steel, or plastic?
  • What is the minimum distance that vent pipes should be from any building opening?
  • Which toxicity classification is for refrigerants with an OEL less than 400 ppm?
  • What is the installation requirement for mechanical fasteners in radiant heating systems?
  • What is the minimum required outdoor ventilation air for a 2000 square foot florist shop?
  • Duct systems for Type I hoods should be constructed with what gauge steel?
  • What is UL 181A ductwork more commonly referred to as?
  • What is the acceptable maximum distance between cleanout openings in grease ducts at changes in direction greater than 45 degrees?
  • Electric pool and spa heaters must be tested in accordance with which standard?
  • What is the term for a joint created by the joining of metal parts in a molten state?
  • Unions requiring gaskets or packings shall not be used in _____ lines.
  • What type of air is prohibited from being recirculated in swimming pool areas?
  • What is the minimum elevated temperature rating for smoke damper leakage as specified?
  • Intake openings located in flood hazard areas must be at or above what level?
  • Oil-fired furnaces are required to be tested in compliance with which standard?
  • Which type of hood is specifically designed for obtaining clean air in kitchen environments?
  • How far must underground tanks be from the nearest property line?
  • Environmental air exhaust outlets must be located how far from operable openings into buildings for all occupancies except Group U?
  • In what contexts are portable space heaters explicitly discouraged?
  • What must be done for all ductwork in conditioned spaces within the North Carolina Mechanical Code?
  • What is a key feature of a forced-draft venting system?
  • According to duct installation guidelines, ducts must be __________.
  • Which standard is used for testing electric coin-operated clothes dryers?
  • What must grease duct reservoirs be provided with for maintenance purposes?
  • Where should filters be installed in relationship to heat exchangers or coils?
  • Which description best fits heavy-duty cooking appliances?
  • What is the required minimum thickness of metal for a vent connector used with a low-heat appliance having a diameter of 14 inches?
  • Which type of dwellings is exempt from the sauna heater warning notice requirements?
  • Which of the following closure systems is commonly used for sealing flexible air ducts according to UL 181B?
  • What is the term for a joint made by bolting together a pair of flanged ends?
  • At what height above the lowest portion of the interior of the chimney flue should connectors connect?
  • What is the minimum height at which every exhaust outlet located above the roof must terminate?
  • How should joints in refrigerant piping be treated in field installations?
  • When the maximum allowable working pressure of a boiler exceeds which pressure, two bottom blowoff valves are required?
  • In flood-hazard areas, mechanical systems must be placed at or above what level?
  • What type of collectors must be listed and labeled with specific information by the manufacturer?
  • Masonry fireplaces must be constructed in accordance with which code?
  • A certificate of test is required for all systems containing how many pounds or more of refrigerant?
  • What must condensate pumps located in uninhabitable spaces do in the event of a failure?
  • What must the air transported to occupied spaces through rock or dust-producing materials be?
  • What is the general function of a boiler in a heating system?
  • Under what condition is a single door permitted for connecting a parking garage to a fuel fired appliance room?
  • Machinery rooms should not have open flame devices or hot surfaces over what temperature permanently installed?
  • What condition results in ductwork above a drop ceiling being excluded from the "exposed" category?
  • Shutoff valves should be installed on connections to what type of equipment?
  • What is necessary to ensure safe operation in solar energy systems for managing thermal conditions?
  • Which gas is classified under group A1?
  • How far must exhaust outlets terminate from adjacent buildings and property lines?
  • What gauges are mandatory for every hot water boiler?
  • For Group A1 or B1 refrigerant liquid lines, what is the maximum size of Schedule 40 carbon steel pipe allowable?
  • What is defined as an enclosed portion of the building structure that allows air movement within an air distribution system?
  • Which joint is formed using solvent or solvent cement in thermoplastic piping?
  • How close to the edges of the duct must horizontal cleanout openings be installed?
  • What is necessary in a double indirect open spray system in case of refrigerant rupture?
  • Energy recovery ventilation systems are commonly used to improve what aspect of HVAC systems?
  • Which installation requires adherence to the manufacturer's installation instructions for clearance to combustibles?
  • Clothes dryer exhaust ducts should not be located within assemblies required to be what rating?
  • What is the definition of a vent according to mechanical code?
  • Where should cleanout openings be located on grease ducts?
  • What type of flexible duct is limited in length according to the standards discussed?
  • Notches in the top or bottom of joists should not exceed what fraction, and cannot be located in which portion of the span?
  • What code governs the installation of evaporative cooling equipment related to the protection of potable water?
  • What is a prohibited return air plenum application related to?
  • What is the minimum vertical termination height for mechanical draft systems adjacent to walkways?
  • What should the maximum and minimum allowable operating temperatures for thermal storage units be based on?
  • An insulation shield for vents passing through insulated assemblies must be made from what gauge sheet metal?
  • Which statement best describes a registered design professional's qualifications?
  • When are machinery rooms required in relation to refrigerant quantities?
  • To what should the auxiliary pan drain discharge to alert occupants?
  • What level of fuel oil storage is prohibited above ground for 1-2 family dwellings?
  • Plume discharges must be positioned at least 5 feet above or 20 feet away from any __________ to a building.
  • How should the joints in dryer exhaust ducts be aligned?
  • What must be kept at least 10 feet away from any operable openings or air intake?
  • What is the maximum flame spread index allowed for duct coverings to reduce the spread of fire and smoke?
  • An area within the building thermal envelope that is cooled or heated directly is best described as?
  • A solid fuel-burning appliance or fireplace shall not connect to a chimney passageway venting another __________.
  • What type of expansion tanks requires shutoff valves to be installed at connections?
  • Where should the manual emergency control device be located?
  • What classification is given to areas where refrigerants are considered for leakage classification?
  • Solar equipment exposed to vehicular traffic must be installed at what minimum height above the finished floor?
  • What standard must factory-built fireplaces be tested in accordance with?
  • How far must the bottom of the duct termination be above the areaway bottom?
  • Which systems are classified as high probability systems?
  • How must all joints in duct systems be treated to ensure proper functioning?
  • Medium-heat appliances operate with combustion products that span which temperature range?
  • What type of separation is required when connecting a parking garage with any room containing a fuel-fired appliance?
  • What is the main cooling method employed by an air washer system?
  • What standard must be followed for ventilation when rubber cement is used or mixed?
  • Under what condition is taking return air from a kitchen not prohibited?
  • What is the minimum clearance from combustible construction required for a Type I hood unless protected by approved methods?
  • How far must linings be interrupted from electric-resistance and fuel-burning heaters in a duct system?
  • How often should duct inspections occur according to best practices in construction?
  • Masonry chimneys must be constructed in compliance with which code?
  • What control is required for steam and hot water boilers?
  • What is typically expected from the installation of a grease duct?
  • For a residential system, what is the minimum thickness of 16-inch aluminum duct?
  • What type of barriers must protect appliances that are subject to mechanical damage?
  • Vents must terminate at least how many feet above a forced air inlet located within 10 feet?
  • Which joint is made in thermoset plastic piping using an adhesive that forms a continuous bond?
  • If return air risers serve two or more stories, at what design capacity must smoke detectors be installed at each story?
  • What is UL 181A ductwork commonly referred to as?
  • Which code must the potable water system comply with to prevent backflow?
  • What should be done to ensure ducts do not obstruct exhaust flow?
  • What is a room primarily utilized for the installation of a boiler called?
  • In what type of area is the use of corridors for conveying return air not prohibited?
  • What is the minimum pitch of rise that must be maintained when installing a connector?
  • Electric duct furnaces must be tested in accordance with which standard?
  • To what standard must duct installations comply for makeup air ducts?
  • What is the primary purpose of insulation in exterior ducts?
  • What is the term used for the piping that should maintain a minimum slope?
  • What should you ensure about boiler installations in relation to their flooring?
  • What is the minimum flash point required for liquid adhesive coatings used on filters?
  • What is the main purpose of designing equipment service rooms to prevent contamination spread?
  • What is required when a grease duct serving a Type I hood penetrates a ceiling?
  • Below grade installations must be provided with which of the following?
  • Which of the following is specifically mentioned as a prohibited application for energy recovery ventilation systems?
  • Filters must be installed such that all return air is filtered upstream from which of the following components?
  • Where should a relief valve be installed in relation to the pump discharge line?
  • What is generally required for a new mechanical installation according to North Carolina's mechanical code?
  • When a duct is contained within a wall cavity, what is the maximum nominal diameter allowed for the duct?
  • The minimum size of tubing for the supply line is ____-inch (9.5 mm) od tubing.
  • When is it necessary to provide additional drain systems?
  • What is the primary purpose of prohibiting energy recovery ventilation systems in certain applications?
  • What is the minimum temperature that the fire damper actuation device must not fall below?
  • Fire dampers must comply with which standard?
  • What do clothes dryers need to comply with according to the Mechanical Code?
  • What is the maximum air temperature for gypsum boards to be used in air ducts?
  • Where must clothes dryers exhaust to?
  • What is a purpose of a smoke damper installed in ducts?
  • In cases where code provisions conflict with equipment listings, which must be followed?
  • What is the minimum size for a dryer exhaust duct?
  • What is the minimum exhaust rate at which makeup air must be provided for exhaust hood systems?
  • According to joist notching guidelines, notches at the ends of joists should not exceed what fraction of the joist depth?
  • Which component is characterized as an enclosed part of a building designed for air movement as part of an air distribution system?
  • What material is typically used for the construction of nonmetallic ducts?
  • What must tanks be made to allow for installation and removal from dwellings?
  • Where should return air grilles not be located?
  • What is the design capacity limit for fan powered terminal units before smoke detectors are not required?
  • When are smoke detectors not required according to air distribution system capabilities?
  • Which type of refrigerant systems is considered high probability for leakage?
  • What is the term for air being removed from a space and directly conveyed to the atmosphere?
  • Where should a pressure relief valve be installed in a hydronic piping system that has been reduced in pressure?
  • Which type of clothes dryers are exempt from the general exhaust requirements?
  • Trifluoromethane falls under which refrigerant group?
  • Which type of temperatures must not be exceeded by installed devices in a machinery room?
  • Factory-built fireplaces must be _________ and installed according to the conditions of the listing.
  • Hearth extensions must serve what purpose in relation to safety?
  • What is the minimum height requirement for suspended equipment above adjacent grade?
  • What must be done for field-erected refrigeration systems concerning testing?
  • What is the pressure testing requirement for a hydronic system before backfilling?
  • Above what height must exhaust outlets located above the roof terminate above the roof surface?
  • Oil-fired unit heaters must be tested in compliance with which standard?
  • What does exfiltration refer to in building environments?
  • What is the minimum R-value for insulation beneath radiant piping in slab-on-grade applications?
  • Which kind of holes should not be located at the same section of a stud as a cut or notch?
  • All Type I hoods must be constructed with a minimum of which gauge steel?
  • According to the code, what material can be used for duct construction for domestic range hoods?
  • What type of valve must steam boilers be equipped with at the bottom?
  • Shutoff valves must be installed on the building supply and return of what type of utility system?
  • How should joints and connections be configured for the pressure of the hydronic system?
  • What is the main function of equipment found in building systems?
  • What is the height requirement for the passageway that provides access to appliances under floors?
  • Where must grease duct reservoirs be located?
  • What types of cooking appliances require Type I hoods installed above them?
  • Which standard applies to oil-fired pool and spa heaters?
  • What is the minimum opening area required for a closet designed for dryer installation?
  • How must air ducts formed by gypsum boards be treated within air-handling systems?
  • What is the minimum flash point for liquid adhesive coatings used on filters?
  • What is the required thickness for sheet steel used in duct construction according to the Mechanical Code?
  • What qualifies as a high-heat appliance?
  • What classification of duct material must nonmetallic ducts comply with?
  • When operating duct systems, what must be monitored to ensure safety and compliance?
  • How far horizontal separation is required between ducts conveying explosive substances and exterior walls?
  • How many separate return-air intakes must be installed on each level of a multi-level structure?
  • What must be done to solar energy systems regarding pressure and temperature limits?
  • What should be installed to maintain clearance near a vented wall furnace?
  • In pipe testing, what gauge is required for increments when testing below 10 psi?
  • What is the minimum width of metal straps used for supporting ducts in one-and two-family dwellings and townhouses?
  • When the heat-serving element of a sauna heater thermostat is not integral to the sauna heater, what is the maximum distance it should be from the ceiling?
  • Incidental air movement from pressurized rooms is allowed when located where?
  • What labeling requirement applies to cooking appliances?
  • At what height is a permanent means of access required for appliances?
  • Which type of system's air passages are not classified as air ducts?
  • Why is it critical for makeup air systems to work simultaneously with exhaust systems?
  • What is the primary function of ductwork labeled under UL 181 standards?
  • When must makeup air systems operate with the exhaust system?
  • What is the maximum length allowed for flexible air connectors?
  • Duct linings must be removed how many inches downstream of a fuel burning duct heater?
  • Where should the controlling thermostat for a floor furnace ideally be installed if in a different room?
  • What is the minimum distance that return air openings must be from an open combustion chamber?
  • What qualifies an occupiable space?
  • In dwellings with 1,600 square feet or less of conditioned area, how is a central return classified?
  • What is the testing standard for electric furnaces?
  • Why should duct heaters be accessible?
  • What is the minimum clearance required for appliances designed for natural draft venting from vent terminals to any openings for combustion products entry?
  • For all mechanical air intakes, what is the minimum distance from exhaust outlets?
  • How must safety and relief valves be installed in relation to the opening on the boiler or pressure vessel?
  • What is an important characteristic of a Plastic Solvent Cement Joint?
  • To whom must a copy of all test documents and manufacturer's data reports be submitted?
  • In which of the following scenarios are space-heating systems not required?
  • What is the maximum allowable temperature differential between makeup air and the conditioned space?
  • What is the minimum clearance above finished grade for duct termination unless an areaway is provided?
  • The transfer fluid in a hydronic system must be compatible with what?
  • What is a common purpose for fire and smoke dampers?
  • What is the primary concern when installing joists with notches and bored holes?
  • What is the general requirement for safety relief valves regarding the potential for damage?
  • What feature must be included in ductwork for dryer exhaust systems to ensure proper functionality?
  • In terms of system components, what should be isolated in machinery rooms?
  • What is a key requirement for maintaining the thermal comfort of indoor spaces?
  • Ducts that penetrate a private garage wall must be constructed of which material?
  • What must the discharge line of a relief valve do according to code?
  • What should not be used to join ducts if it protrudes into the inside of the duct?
  • What is prohibited regarding return air between dwelling units?
  • What type of material should hangers and brackets be made of according to the code?
  • Where should an indicating test gauge be connected during a test?
  • What is the minimum velocity allowed in an exhaust hood duct system?
  • What is the minimum elevation above the floor surface for ignition sources located in hazardous locations?
  • Refrigerants of groups A2, A3, B2, and B3 used in machinery rooms must meet the requirements of Class 1 Division 2 of ________.
  • What device is used to protect hot water boilers?
  • Which condition must be met for low-water cutoff not to be required for certain boilers?
  • Field applied enclosure systems for Type I hoods must be what to meet the required configuration?
  • What type of damper is required to prevent the passage of flame and hot gases in certain duct systems?
  • What is the chemical formula for ammonia?
  • Which of the following surfaces are flexible air connectors NOT allowed to pass through?
  • What is the purpose of a press joint in mechanical systems?
  • What is the recommended construction material for tanks to prevent corrosion?
  • For grease hood exhaust duct systems less than 75 feet, what is the minimum slope required?
  • What is the primary purpose of ventilation air?
  • What safety feature should be included in systems that generate explosive vapors?
  • What must be installed between the hood and the gypsum or cementitious wallboard?
  • What does the term flash point refer to?
  • What mechanism can halt the AHU serving a corridor in the event of smoke detection?
  • What is required for using a corridor as a source of makeup air for exhaust systems?
  • What is required for mechanical exhaust systems for environmental air?
  • What is the condition of piping that cannot degrade or corrode when in contact with building materials?
  • Hangers and brackets used in mechanical installations must be of what type?
  • In which scenario are smoke detectors not required in the return air system?
  • What happens if a fan-powered unit has a design capacity greater than 2,000 cfm?
  • What criterion must be met for alterations to trusses, including cuts, notches, and holes?
  • According to UL standards, what is the compliance required for dampers?
  • Which type of refrigerants require special handling due to their flammable nature according to classification?
  • When brick is used for crawl space supports, how should the bricks be assembled?
  • What must be true about furnaces and boilers installed in closets and alcoves?
  • At what pressure do low-pressure boilers operate for steam?
  • Which chapter of the code deals with site-built masonry fireplaces?
  • What is the required temperature rating for gasket and sealing materials in grease ducts?
  • What type of heating system is required to maintain a suitable indoor temperature?
  • What should not be used to connect or install dryer exhaust ducts?
  • In the case of Type I hoods, what is the minimum clearance allowed when using gypsum with certain materials?
  • What type of valve is required for a combination potable water-heating and space-heating system that exceeds 140°F?
  • Unvented gas log heaters can only be installed in which type of fireplace?
  • What is the minimum pressure for hydrostatic testing of hydronic piping systems?
  • In the context of refrigeration systems, what does the term 'make-up air' refer to?
  • Supply tanks larger than 10 gallons must be placed at least how many feet away from any fire or flame?
  • What pressure should connecting offices to public garages maintain?
  • What should automatically stop combustion when water levels drop below the safe level?
  • What is the primary purpose of a boiler room?
  • What is the testing standard for commercial electric cooking appliances?
  • Exhaust fans for a public bathroom shall be sized at how many cfm per flushing unit if the fan is continuous?
  • What rating should smoke damper leakage be classified under?
  • What component is crucial for a press joint to be labeled as compliant?
  • What documentation is required for appliances located in hazardous locations?
  • What does the term "clearance" refer to in mechanical installations?
  • What is required to ensure proper handling of combustion byproducts from condensing appliances?
  • What happens if the pressure in the system exceeds the limits specified for the relief valve?
  • What is the necessary height for exhaust discharge above adjoining grade?
  • How far above the earth must ducts be installed in accordance with the regulations?
  • What must collectors indicate on their labels regarding heat transfer fluids?
  • What gauge should be present in conjunction with the water-gauge glass in steam boilers?
  • How should underground tanks be set and surrounded?
  • Products of combustion from fuel-burning appliances must be discharged to what?
  • Which type of air includes both outdoor air and recirculated air to ensure comfort in designated spaces?
  • In which direction shall ducts slope toward?
  • The actuation device operating temperature of a ceiling radiation damper must be what above the normal temperature in the duct system?
  • What standard must solid-fuel-fired water heaters comply with?
  • Which code specifies the requirements for combustion air for oil fired appliances?
  • What type of appliance is classified as a direct vent appliance?
  • What is a suitable method for supplying fuel oil?
  • What is the minimum clearance from an underground tank to the nearest wall of a basement, pit, or property line?
  • Which of the following types of joints requires no sealing?
  • What is required to maintain the continuity of the vapor retarder at joints and seams?
  • What should happen to exterior above-grade fill piping when tanks are abandoned or removed?
  • What standard must sauna heaters comply with for installation?
  • What type of steel gauge is required for underground grease ducts?
  • Temporary certificates must comply with requirements specified for which type of services?
  • What marking is required for ground source heat pump loop system piping?
  • Which type of fasteners are explicitly excluded from being used if they protrude into the duct?
  • What must solid-fuel burning appliances be limited to?
  • What is the maximum duration for which a temporary permit can be issued by the code official?
  • Which systems are classified as high probability systems?
  • What feature is essential for every underground grease duct according to installation guidelines?
  • What is the maximum allowable length for transition ducts in a dryer installation?
  • What is the minimum thickness for galvanized sheet steel pans?
  • Under what condition are shutoff valves not required for heat exchangers?
  • What type of appliances must cooking appliances within dwelling units be labeled as?
  • For homes with appliances that are direct vent or unvented, at what exhaust capacity must makeup air be provided?
  • What should be readily observable upon inspection of insulating materials used in thermal barriers?
  • Which of the following describes an unconditioned attic in relation to return air?
  • Under which condition are smoke detectors not required in air distribution systems?
  • What should joints and seams in ducts be if not continuously welded?
  • What ensures visibility of the indicating test gauge to the operator?
  • What is the maximum interval, in inches, for attaching metal straps that support ducts?
  • What must grease ducts have for clearances to noncombustible materials?
  • Which type of electric cooking appliances must comply with UL 197?
  • What type of appliance has combustion products that enter the flue at a temperature of 1,000°F or less?
  • What is a key requirement for materials used in sealing clothes dryer exhaust ducts?
  • How frequently must external duct insulation be identified with manufacturer details?
  • What is the purpose of having smooth inner walls in ductwork for exhaust systems?
  • What action should individuals with poor health take before using the sauna?
  • What defines a space that is not connected to other areas through permanent openings or HVAC ducts?
  • Which of the following joints requires an adhesive for bonding?
  • What is the minimum horizontal slope required for condensate disposal piping?
  • In what situation is the exception regarding duct termination height applicable?
  • What must not allow a section of a solar energy system to be isolated from a relief device?
  • What must be installed over exposed duct liner edges that face opposite the airflow direction?
  • The duration of each test shall be not less than how many minutes?
  • What is the recommended proximity for the heat-serving element of sauna heater thermostats to the ceiling?
  • For other product conveying outlets, what is the minimum distance from operable openings into buildings?
  • What name is given to the pipe that connects a fuel appliance to a chimney?
  • In which direction should the insert end of the dryer duct extend?
  • Commercial clothes dryers are categorized as which type?
  • Which legislation outlines the prohibitions for energy recovery ventilation systems in North Carolina?
  • An unvented gas log heater can only be installed in a factory-built fireplace that has been tested and labeled according to which standard?
  • Temporary installations must be compliant with which type of requirements?
  • Exhaust from mechanical ventilation systems must be discharged at least how many feet from property lines or openings into buildings?
  • Where should cleanout locations be legibly identified?
  • How should cutting, notching, and boring in structural steel framing be conducted?
  • What type of vestibule is required for the connection of a parking garage to a room with a fuel fired appliance?
  • What is the maximum permitted depth for notches in the top or bottom of joists?
  • Which material is required for Type I hood construction?
  • What is the minimum exhaust rate required for an exhaust fan in a public bathroom with intermittent operation?
  • How should clothes dryers be exhausted according to the code?
  • Which type of duct tape is not permitted as a sealant on metal ducts?
  • Which type of exhaust system requires ducts that discharge to the outdoors through specific materials?
  • What is the maximum temperature for air temperature when gypsum ducts are used?
  • What is the minimum thickness required for sheet steel used in ductwork for dryer exhaust?
  • What materials are considered acceptable for factory built commercial kitchen grease ducts as exceptions?
  • What is the definition of “access (to)” as mentioned in the code?
  • How should the relief valve discharge?
  • What is the main restriction regarding return air from one residential living unit?
  • What is the minimum distance for return air openings in kitchens from cooking appliances?
  • Return air from one dwelling unit should not be discharged into which of the following?
  • Single or combined mechanical exhaust systems must be designed to be what?
  • What is the role of a drain pan connected to a cooling coil in a furnace?
  • Which of the following is NOT a requirement for intake opening location?
  • What is the minimum flashpoint of liquid adhesive coatings used on filters?
  • According to installation requirements, how should grease duct reservoirs be constructed?
  • What is the temperature threshold that requires a specific valve for water supplied to the potable distribution system?
  • If the combined capacity of common supply and return air systems exceeds 2,000 cfm, what is required?
  • For which type of boilers is a low-water cutoff not required under certain conditions?
  • Which of the following is an essential characteristic of both duct coverings and linings?
  • Which gases are the deterrent for the mechanical ventilation in enclosed parking garages?
  • In energy recovery ventilation systems according to NCMC, which kitchen systems are specified?
  • According to the standards, what must the construction of masonry heaters comply with?
  • What is the purpose of drain pans in HVAC installations?
  • What is the purpose of outdoor air ventilation systems in buildings?
  • Flexible air ducts are subject to limitations on what aspect according to the code?
  • Before operating a refrigeration system, which specific component is usually not required to be tested?
  • When must individual shutoff valves be included in a boiler installation?
  • Which standard must be met for reused refrigerants of the same owner?
  • What type of vents are triple lined stainless steel?
  • What is the required air handler capacity that mandates the installation of smoke detectors?
  • What is necessary if ducts penetrate fire-rated assemblies?
  • What does the term "unprotected open flame" refer to in the context of heating appliances?
  • What type of appliance derives all combustion air from the outside atmosphere?
  • When vents pass through attic space, the shield must terminate not less than ___ inches above the insulation materials.
  • What is the minimum scale graduation required for a pressure gauge?
  • What type of ventilation system is NCMC 514.2 considering when discussing energy recovery limitations?
  • Combustion air ducts that traverse rated construction without protective dampers must be?
  • How many feet higher must Type L vent terminations be than any portion of a building within 10 feet?
  • Where should moisture and combustion products from dryer exhaust systems be conveyed?
  • What must hot water and steam boilers have before being operationally tested?
  • To minimize fire hazards, Type I hoods for solid-burning cooking appliances must discharge to which type of exhaust systems?
  • Under what condition are ductless range hoods not required to discharge outdoors?
  • What is prohibited concerning engineered wood products in regards to cuts and notches?
  • In order to ensure the removal of the largest component of the appliance, the passageway must be large enough for what?
  • Steam boilers must be equipped with what type of safety device?
  • What does "Approved" refer to in the context of the code?
  • What is the minimum slope requirement for duct systems to prevent grease accumulation?
  • Are metal band duct clamps required to be listed?
  • In suspended floor applications, what is the minimum R-value for insulation in the joist bay cavity?
  • What type of dry cleaning system uses flammable liquid solvents with a flash point at or above 100ºF and below 140ºF?
  • What type of vapors, fumes, or dust must not be conveyed by dust, stock, and refuse systems with energy recovery ventilation?
  • What must the duct smoke detectors in required monitored facilities report?
  • How far below the adjoining grade must the passageway depth be before specific wall lining is required?
  • What standard must fire dampers comply with?
  • What type of fuel-burning appliances must be listed and labeled according to ASTM E 1509?
  • What configuration is essential for condensate drain lines?
  • What is the term for the pressure difference that facilitates the flow of air and combustion products to the atmosphere?
  • Which of the following appliances is exempt from the prohibited locations rule for fuel-fired appliances?
  • When an oil burner is served by a tank, what must be installed if the fuel supply line comes from the top of the tank?
  • What must be prevented on the exterior of primary condensate drain piping?
  • What is the maximum allowed length for a horizontal run of a single-wall connector?
  • A duct and air transfer openings that penetrate a ceiling membrane of a fire-resistance rated assembly must be protected with what?
  • What is essential for an approved reduced clearance protective assembly?
  • How long should a timer for the main burner operation be able to operate?
  • Nonmetallic pipes must be installed in which locations according to the code?
  • What is the purpose of a Type II kitchen hood?
  • What standard must supply tanks conform to when installed inside of buildings?
  • What is the primary function of the building shutoff valve?
  • What is the maximum air capacity in cubic feet per minute for 8-inch joists used for return air?
  • What type of cooking appliances produce grease and smoke requiring Type I hoods?
  • How far must guards extend beyond each end of the opening?
  • You can have multiple appliances served by one chimney, but only __________ per appliance or fireplace.
  • What is the maximum allowed diameter of a bored hole in any wood stud as a percentage of the stud depth?
  • What must be secured in place when a vent passes through attic space to prevent displacement?
  • What is the specification for a modular boiler regarding its input rating?
  • How far must ducts conveying explosive or flammable vapors be located from property lines?
  • What is the primary function of a ceiling radiation damper?
  • What risk does a loose cover on a fill opening present?
  • What type of vent is specifically listed for use with pellet-fuel-burning appliances?
  • Oil fired boilers and their control systems must conform to which UL standard?
  • Roof and wall penetrations must be treated how to prevent entry of water, rodents, and insects?
  • In commercial kitchens, how should makeup air impact the exhaust system?
  • Which of the following is a requirement for the ventilation system in a dwelling unit?
  • Which system is responsible for introducing fresh air into a space while removing stale air?
  • Which category would NOT typically involve a low-heat appliance?
  • Electric furnaces must adhere to testing standards defined by which of the following?
  • Flexible connectors and hoses shall be listed and labeled in accordance with __ __.
  • What must be included by the designer on the building plans regarding fire dampers?
  • What must local exhaust systems be capable of exhausting in the specified areas?
  • Indirect systems are classified as low probability if what conditions are met?
  • According to grease duct standards, reservoirs must extend across what area?
  • Type I hoods must be installed over cooking appliances that produce what types of byproducts?
  • Commercial clothes dryers are categorized as which type?
  • According to safety standards, clothes dryers must exhaust in accordance with what?
  • What type of air leakage refers to the loss of conditioned air to unconditioned spaces?
  • What is prohibited regarding clothes dryer exhaust ducts?
  • What is the required distance for ducts conveying explosive or flammable vapors from property lines?
  • What must be provided to manually disconnect the control circuit?
  • What type of screens should be used to protect exhaust openings that terminate outdoors?
  • Fuel-fired appliances shall not be located or obtain combustion air from which of the following?
  • What type of detectors are required for installation in air distribution systems?
  • What is the minimum load that floor registers must resist without structural failure?
  • What defines a Type I kitchen hood?
  • Masonry fireplaces must comply with which building code?
  • Solar equipment exposed to vehicular traffic shall be installed at what minimum height above the finished floor?
  • Which item is not permitted to be installed to maintain clearance from vent terminals?
  • What is the term for a building or portion thereof that contains not more than two dwelling units?
  • What type of heating appliance must be separated by 2 hour rated construction?
  • Nonmetallic mechanical fasteners for ducts must be listed to which standard?
  • What is the minimum clearance required for a grease duct serving a Type I hood to combustible construction?
  • What is the condition for return air from a room or space related to the supply air flow rate?
  • What type of control is required for steam and hot water boilers?
  • According to regulations, how should clothes dryers be installed?
  • What types of services can utilities be temporarily supplied before final completion?
  • Which index measures the smoke developed by a material?
  • Which type of cooking appliance utilizes open flame combustion of solid fuel?
  • Nonmetallic ducts must be constructed with which classes of duct material?
  • When multiple connectors enter a common vent, where should the smaller connector be positioned?
  • What type of air is a combination of outdoor and transfer air meant to replenish exhausted air?
  • What is the acceptable flash point for kerosene or hydrocarbon oil classed as fuel oil?
  • What type of ducts must be a single length and comply with UL 2158A?
  • What is the design air temperature for air to be conveyed in flexible air ducts and connectors?
  • Which hoods are installed over light duty cooking appliances that produce heat or moisture?
  • Where can site-built masonry fireplaces be found in relation to the Building Code?
  • Where should return air not be sourced from according to the mechanical code?
  • What is a device actuated by another device that governs the operation of succeeding devices called?
  • The flash point of transfer fluid in a hydronic system should be at least how many degrees above the maximum operating temperature?
  • What must each boiler or modular boiler have in relation to shutoff valves?
  • Duct smoke detectors must comply with which standard?
  • What is the purpose of a duct in construction?
  • Additions and alterations to a mechanical system must conform to requirements for what?
  • What is a key consideration for installations involving a power exhauster based on safety?
  • What is essential for the system components to prevent being damaged by freezing?
  • Combustion air must be provided according to which of the following?
  • What is the required height for appliances installed where motor vehicles can pass beneath them?
  • What type of anchorage connector devices are not required to have guards during installation?
  • What type of device is required to protect solar energy system components from exceeding pressure and temperature limitations?
  • For which type of appliance is the installation explicitly stated to adhere to the terms of listing?
  • What is the required cross-sectional area for an areaway if the duct termination is less than 12 inches?
  • Which requirement is shared by all cooking appliances?
  • Vents of which type of installation incorporates integral venting means, according to exceptions?
  • What is the minimum extension required for concrete or masonry under appliances above the adjoining grade?
  • What is the minimum diameter of a sphere that should not pass through guards for roof-mounted appliances?
  • Which type of system is NCMC 514.2 specifically cautioning against energy recovery ventilation installation?
  • What type of joints can PE-RT tubing use as per the provided regulations?
  • Which type of draft is generated by the operation of a fan, blower, or ejector?
  • What nominal diameter should the exhaust duct size be for clothes dryers?
  • Which of the following is necessary for protection against a vacuum in solar energy system components?
  • The code official is granted the authority to do what regarding temporary permits and services?
  • When replacing heating or adding cooling equipment in a crawl space, what is required for the existing ductwork?
  • What temperature differential should makeup air not exceed in a conditioned space?
  • What should the joints and seams of ductwork generally comply with according to UL 181A?
  • What is the maximum design temperature of air to be conveyed in flexible air ducts and connectors?
  • In an indirect closed system, where does the water flow after being cooled?
  • Which standard must liquid adhesive coatings used on filters not have a flash point lower than?
  • What is a chimney primarily used for?
  • What is crucial to note about manual dampers in solid fuel-burning appliances?
  • What is the purpose of ventilation openings in sauna rooms?
  • What is the required standard for stationary engine generator assemblies?
  • When a code provision is less restrictive than the conditions of the listing, which should be followed?
  • Which type of air refers to ambient air entering a building through ventilation systems or natural openings?
  • Which guideline does not allow flexibility in return air plenum applications?
  • The duct systems must have linings removed for how many inches downstream of a fuel-burning duct heater?
  • When sizing a fuel oil system, which factor is primarily considered?
  • Nonmetallic ducts must be constructed using which classification of duct material?
  • What is the maximum air capacity for panned joists that are 16 inches on center using 8-inch joists?
  • What is the minimum distance required from mechanical air intakes to exhaust openings?
  • What criteria must cleanouts meet for them to be effective?
  • What is the minimum ventilation requirement for mechanical rooms with refrigerant systems?
  • What is the maximum length of listed air duct material?
  • Which type of heater is prohibited to achieve compliance for space-heating systems?
  • Which of these air temperatures exceeds the maximum permissible for certain air ducts?
  • What is the purpose of a fan interlock in electric duct heaters?
  • The hearth extensions from a fireplace stove must be distinguishable from what?
  • What standard must electric residential clothes dryers be tested in accordance with?
  • What marking is assigned for pressure-sensitive tape used in ductwork according to UL 181A?
  • On which line should a relief valve be installed for fuel-oil-heating appliances?
  • What is the recommended distance of exhaust openings from any operable openings into buildings for Group U occupancies?
  • What is the benefit of having labeled equipment in buildings?
  • What is the maximum face velocity for return air grilles in non-engineered systems?
  • What is the maximum distance a cleanout opening should be from a change in direction greater than 45 degrees?
  • Which of the following statements about grease duct clearances is true?
  • Flexible connectors and hoses must comply with which standard?
  • What is the size restriction for tenant spaces where corridors can convey return air, specifically in square feet?
  • Which device is installed in a ceiling membrane to limit radiative heat transfer through an air inlet or outlet opening?
  • What is the distance required between environmental air exhaust and mechanical air intakes for all occupancies other than Group U?
  • Outdoor ventilation air requirements for buildings are defined by _____.
  • When measuring flue gases, the temperature must be recorded at the __________ to the chimney.
  • How far must soldering be performed from a plastic-to-metal adapter in a water line?
  • What is prohibited in grease ducts according to the maintenance guidelines?
  • What must be established for insulations used in ducts to ensure safety?
  • Cast-iron fittings shall _____ _____ _____.
  • What is the required minimum flash point for the heat transfer fluid used in a solar system?
  • What must all additions to mechanical systems comply with?
  • How far apart must cleanout openings be spaced in grease ducts that are inaccessible from the hood?
  • What should be done to the pressure setting of a pressure relief valve during testing?
  • Large mercantile occupancies are defined as where more than how many persons gather to buy merchandise?
  • In which locations are fireplaces and solid-fuel burning appliances prohibited?
  • What is the definition of a registered design professional?
  • For boilers with fuel input ratings of 12,500,000 Btu/hr or less, what standard must the controls and safety devices comply with?
  • Shutoff valves shall be installed on the connection to which kind of vessel?
  • In which type of venting system is the removal of gases under nonpositive static pressure accomplished inside the appliance?
  • According to the code, who has the final authority on approving items related to mechanical systems?
  • Which gas may be used to test refrigerant piping?
  • What energy recovery application is exempt from the prohibitions specified in NCMC 514.2?
  • What type of drainage system must be equipped in boiler rooms for disposing of liquid waste?
  • What feature of a hearth extension is crucial for safety according to building codes?
  • Which gauge indicates the amount of pressure in a hot water boiler?
  • What is classified as an extra-heavy duty cooking appliance?
  • Which of the following is an example of environmental air exhaust?
  • How often should refrigerant leaks in machinery rooms be inspected?
  • What should not be present in steam systems that would reduce the capacity of the piping?
  • What is excluded from the definition of an air duct?
  • What must be interlocked with the firing cycle in appliances served by combustion air openings with smoke dampers?
  • What material is mentioned as a possible element installed between the hood and wall?
  • What must ducts connecting to a furnace maintain concerning combustibles?
  • What is the minimum clearance required for commercial clothes dryer exhaust duct to combustible materials?
  • What is not allowed to be installed at the duct or weather cap termination?
  • What type of joints and seams in ducts are continuously welded and exempt from sealing requirements?
  • What must be the least width of the access opening for appliances under floors?
  • What is the primary role of the installing contractor regarding safety controls in boilers?
  • If systems share common spaces but not common ducts and capacity exceeds 2,000 cfm, smoke detectors are __________.
  • Type I hoods are necessary for cooking appliances that produce which of the following?
  • Where should return air not be taken from according to mechanical code standards?
  • Where must class I ducts, duct coverings, and linings be interrupted to provide specified clearances?
  • What is the minimum flash point for the actual heat transfer fluid used in a solar system?
  • In what context should backdraft dampers typically be used?
  • What happens if the heat exchanger in an air washer leaks?
  • Where are exhaust systems permitted to discharge air?
  • Which type of exhaust systems are prohibited from having energy recovery ventilation systems installed?
  • What type of framing must heating panels be secured to?
  • What is referred to as a flue?
  • How must air transported to occupied spaces be treated if produced from rock or dust-producing materials?
  • What term describes equipment or materials that have been tested and listed by a nationally recognized testing agency?
  • What is the primary function of a boiler?
  • The minimum clearance for vent terminals of natural draft venting appliances is how many inches?
  • If a duct is welded, what is required regarding sealant?
  • What is the main function of the heat exchanger in cooling systems?
  • Which components are generally part of the flexible air duct system?
  • What is the minimum distance that liquid fuel vent pipes should terminate from building openings?
  • What is required for a fireplace system to install unvented gas log heaters?
  • In a system with a single boiler, what type of steam boiler is exempt from the shutoff valve requirement?
  • How must duct connections to flanges of air distribution system equipment be secured?
  • Which type of buildings are exempt from certain provisions of the code?
  • What should be the relation of dryer exhaust systems to other systems?
  • How should oil-fired unit heaters be tested?
  • What is a required characteristic of duct construction for grease ducts?
  • What is the minimum damper rating for penetrations of less than 3-hour fire-resistance-rated assemblies?
  • What defines a space intended for human activities?
  • In case of potential overflow damage, a pump must be located in what type of drain system?
  • Which factor is crucial for ensuring proper duct performance in buildings?
  • Energy recovery ventilation systems cannot be applied to which of the following control systems?
  • In the context of duct penetrations, what must be installed at the floor line in specific cases according to code?
  • What type of duct should residential range hoods be vented with?
  • What must be done to ductwork located in an attic when replacing or adding cooling equipment?
  • What is the minimum height above finished grade for the bottom of a vent termination?
  • In Group R-2, R-3, and R-4 occupancies, how many hours is continuous outdoor air ventilation not required?
  • What is the temperature threshold that necessitates a tempering valve in heating systems?
  • The design air temperature for air conveyed in flexible duct must be less than what temperature?
  • What is a key component of the design of hydronic piping systems regarding drainage?
  • What type of systems does the prohibition specifically exclude in relation to smoke control?
  • What is the primary function of machinery rooms related to refrigerant systems?
  • Any portion of a refrigerant system that is subject to physical damage must be _____ in an approved manner.
  • Minor alterations to existing mechanical systems must meet provisions unless what?
  • Clearances from the tops of boilers to the ceiling should comply with what?
  • Which of the following defines the term 'makeup air' in the context of commercial kitchens?
  • In Group I-2 and I-3 occupancies, what feature must air distribution systems have for emergency situations?
  • Duct smoke detectors must comply with which standard?
  • In building terms, what does the term 'flue' refer to?
  • Mechanical systems that are moved into or within the jurisdiction must comply with what type of installations?
  • Which appliances must be vented in accordance with the code and NFPA 31?
  • In instances of conflict, who is ultimately responsible for ensuring compliance with the provisions of the code?
  • Which type of system is classified as a low-probability system?
  • What must capillary tube and bulb heat-sensing elements in sauna rooms be protected against?
  • What is the purpose of labeling and marking hydronic piping systems?
  • What is a unit heater designed to do?
  • What distance must the edge of a bored hole be from the edge of the stud?
  • Where should the inlet of an exhaust system be located?
  • In addition to protecting the pipe, shield plates must extend at least how many inches above and below the member?
  • Which type of appliances are used in commercial kitchens to cook food and must be ventilated?
  • In mechanical systems, what does 'self-contained' refer to?
  • To which type of dwellings does the maximum flame spread index and smoke developed index not apply?
  • What is the minimum nominal diameter required for a clothes dryer exhaust duct?
  • What temperature should gypsum ducts not exceed?
  • Which type of mechanical joint consists of elastomeric seals and corrosion-resistant tube grippers?
  • Appliance connections to a chimney or vent equipped with a power exhauster shall be made on the __________ side of the exhauster.
  • Which type of copper tubing is restricted in size for certain refrigerant applications?
  • What must be ensured for piping during the pouring of concrete?
  • Domestic electric water heaters must comply with which regulations?
  • What is the minimum internal diameter for condensate waste and drain lines?
  • Who determines the requirements for strength, stability, or proper operation not covered by the code?
  • What is the relationship of independent systems to other exhaust systems according to the regulations?
  • Which organization’s standards should fuel oil piping be tested in accordance with?
  • What is the maximum length allowable for listed air duct material?
  • What type of pipe is required for safety and relief valve discharge?
  • How far should a vent termination be mounted from an oil tank vent or gas meter?
  • In mechanical terms, what does thermal resistance refer to?
  • What is the minimum operating temperature below which Type F steel pipe must not be used for refrigerating lines?
  • What is the minimum copper weight required in commercial kitchen construction?
  • Makeup air systems must operate simultaneously with which system?
  • What type of air is conveyed to or from occupied areas through ducts not associated with heating or air-conditioning?
  • In cases of insufficient evidence of compliance, who bears the expense for tests required?
  • Which of the following is NOT a required characteristic of pipe ends?
  • What is the term for a room that meets specific safety requirements and houses refrigeration systems or their components?
  • What is the minimum clearance distance required around a Type I hood according to the exceptions provided?
  • What is required for openings through concrete or masonry building elements in terms of pipe penetrations?
  • For which type of damper is a supervisory signal reported and not a fire alarm?
  • Where should dryer exhaust ducts for clothes dryers terminate?
  • Which type of tank is permitted to have valves installed?
  • According to the code, what class of material must nonmetallic ducts comply with?
  • What must be present in all steam boilers to ensure safe operation?
  • Type L vents must extend at least how far above any building within 10 feet?
  • What is the air capacity in cubic feet per minute for 10-inch joists used for return air?
  • What information must be labeled on an automatic damper?
  • What percentage of the height of the chimney or vent may the horizontal run of a single-wall connector not exceed?
  • Which air-handling equipment is exempt from emergency controls?
  • What is the minimum clearance from grade level for the lowest portion of a floor furnace?
  • What type of obstruction is mentioned in relation to underfloor passages for appliances?
  • What is the minimum indoor temperature that heating systems must maintain in occupied spaces?
  • The vent termination must be located not less than __________ horizontally from any portion of the roof structure.
  • Piping must be supported at distances not exceeding the spacing specified in which of the following?
  • What is the minimum thickness of the steel shield plates required for protecting piping?
  • If a tenant space is 1,000 square feet or less, what is permitted regarding corridors?
  • What is the minimum height requirement for ducts conveying flammable vapors above adjoining grade?
  • In HVAC systems, which type of dampers are not approved for dynamic operations during a fire?
  • What is the distance requirement for all environmental air exhaust from property lines?
  • What must be maintained between heating panels and elements when fastening?
  • What is required to be provided under the auxiliary drain pan?
  • The fire damper actuation device's operating temperature shall be approximately how many degrees above normal?
  • Safety and safety relief valves are set according to which specification?
  • Transition duct connectors must comply with which standard?
  • Stationary fuel-cell power plants must be tested in accordance with which standard?
  • What is the standard minimum requirement for clearance of ducts to combustible materials?
  • What type of protection is required for piping installed in concealed locations near the edges of supporting members?
  • Equipment located outside a building must comply with occupancy classification if it is within how many feet of a building opening?
  • What must the label on factory-built collectors include?
  • Exhaust hood systems exhausting over what amount of air must have makeup air provided?
  • What should be prevented from being valved off in a solar energy system?
  • Fireplace inserts installed in fireplaces must be listed and labeled according to which standard?
  • Appliances must be installed at a minimum clearance of how many feet above the floor in private garages?
  • What is required for maintaining condensate drain lines?
  • What must be provided during periods of occupancy according to the ventilation standards?
  • The inlet side of the power exhauster is meant to draw the exhaust _____ of the appliance, not push it through.
  • Before backfilling header trenches, what must be done according to the code?
  • For installations that could potentially affect structural integrity, what is critical to consider?
  • What is the minimum distance required between the lowest edge of a grease filter and the cooking surface of an appliance without exposed flame?
  • How far must a door swing be from an air inlet or outlet of a vented wall furnace?
  • What type of heat can be recovered without limitation according to the exception for energy recovery ventilation equipment?
  • To minimize the occurrence of what issue must the flow velocity in a hydronic piping system be controlled?
  • What is defined as a combustible assembly?
  • What is the required distance a floor furnace should be from a corner when wall register models are used?
  • Which type of dry cleaning system uses solvents with a flash point below 100ºF?
  • Make-up air for machine rooms shall be provided through openings located to avoid intake of _____.
  • In which piping systems should shutoff valves be installed according to specified sections?
  • What is the maximum height for air inlets or exhaust openings in fuel-dispensing areas above the floor?
  • Return air openings should not be located within which types of spaces?
  • Which toxicity classification applies to refrigerants with an occupational exposure limit of 400 ppm or greater?
  • What aspect of thermal storage units must be labeled for user awareness?
  • What must be done to ensure the safety of the transfer fluid?
  • What must liquid combustion by products of condensing appliances be done with according to installation instructions?
  • Upon activation of a smoke detection system, air distribution systems part of a smoke control system shall switch to which mode?
  • How frequently must exhaust ducts be supported and secured during installation?
  • What is NOT required for HVAC systems regarding calculations for permitting and inspections?
  • How should electrical equipment generating flammable vapors be operated in relation to the ventilation system?
  • What is the maximum wall thickness of carbon steel pipe that must be used for Group A2, A3, B2, or B3 refrigerant liquid lines for sizes 1-1/2 inches and smaller?
  • Type I hoods must be equipped with which type of filter?
  • Which space is prohibited from being the source of return air?
  • How long must the outdoor air ventilation system operate in a 4-hour period for certain Group R occupancies?
  • What is the minimum distance that a drapery or combustible object should be from the register of a floor furnace?
  • What is the maximum depth for notches at the ends of joists?
  • What is the minimum height that vents shall terminate above the highest connected appliance flue collar?
  • Installation of mechanical systems must not adversely affect the integrity of which building components?
  • What construction type is required for the corridor ceiling to be used as a return air plenum?
  • What must access doors for sauna heaters ensure for normal servicing?
  • What must piping embedded in concrete undergo before the concrete is poured?
  • What happens if water circulation stops in relation to low-water controls?
  • If a floor furnace is sealed to prevent water entry, what is the minimum clearance from grade?
  • Electric commercial clothes dryers shall be tested meeting which standard?
  • Intake openings shall not be located less than 10 feet from _____ ____.
  • What is the minimum distance other product conveying outlets must be from property lines?
  • What is necessary to prevent flooding issues in tanks during design flood conditions?
  • What type of ducts are prohibited for clothes dryer exhaust systems?
  • Why is it important to keep ventilation intakes away from property lines?
  • Refrigeration systems are classified based on which factor?
  • Which standard is applicable for nonmetallic duct construction?
  • What must ductless mini-split systems with condensate include?
  • All joints and seams in duct systems must be _____ to maintain vapor retarder continuity.
  • What is the primary function of a vent as defined in mechanical codes?
  • The pump shall automatically shut off the _____ when not in operation.
  • Which of the following components are generally exempt from being tested under the Mechanical Code?
  • What does the R-value measure in thermal insulation?
  • What standard must supply tanks conform to for above-ground installations?
  • What is the maximum total area in square feet that can be served by one return in split-level structures?
  • What is defined as a closed heating appliance that supplies hot water or steam for various purposes?
  • Where should components containing refrigerant be located if the quantity exceeds specified amounts?
  • What is the required ventilation during the use of a room or space?
  • What is the required minimum width for grease duct reservoirs?
  • What is the maximum smoke-developed index for duct coverings when tested to ASTM E 84 or UL 723?
  • Type B vents consist of which type of pipe?
  • What type of screens must exhaust openings that terminate outdoors be protected with?
  • Which of the following appliances is specifically covered under UL 896?
  • What should the controlling airflow system for garages be equipped with?
  • An outdoor air ventilation system consisting of a mechanical exhaust system, supply system or combination thereof shall be installed for _____ dwelling unit.
  • How thick must concrete encase metallic underground ducts without an approved protective coating?
  • Ducts exposed within conditioned space do not require sealing under certain conditions, true or false?
  • What percentage of the design pressure or pressure relief device setting must joints in air ducts withstand?
  • What is required for every steam boiler in addition to a pressure gauge?
  • The passageway for appliances under floors should not exceed how many feet in length from the opening to the appliance?
  • What can occur if condensate does not discharge properly?
  • What should the pan be larger than, according to code?
  • What should be used to protect buried piping and underground tanks?
  • The installation of factory-built chimneys must adhere to which of the following?
  • At what setting should safety and safety relief valves be calibrated?
  • What type of refrigerant system requires all piping and fittings to be isolated for classification?
  • Which of the following is the required distance from operable openings into buildings for ducts conveying flammable vapors?
  • Which of the following does NOT need to be constructed to ASME standards?
  • What is the minimum depth required for a drain pan?
  • What instructions must be followed when converting an appliance for different fuel usage?
  • At what temperature are high-heat appliances defined to operate at the point of entrance to the flue under normal conditions?
  • Which category of kitchen exhaust systems is designated as Type II?
  • For what purpose must connectors maintain a proper pitch?
  • What material should be used to seal the annular space where a clothes dryer exhaust duct penetrates a wall or ceiling membrane?
  • Which type of ducting is specified for dryer installations in residential settings?
  • Which term describes individual and distinct pieces used in construction, such as electrical and plumbing products?
  • What is the primary purpose of ensuring proper vent terminal clearance?
  • What consequence could arise from improper installation of decorative shrouds on factory-built chimneys?
  • What must be ensured for systems generating explosive vapors in terms of operational safety?
  • What should the spacing be between cleanout openings in inaccessible sections of grease ducts?
  • Insulated exterior ducts must be protected with which type of barrier?
  • What is the purpose of providing cleanout openings in grease ducts?
  • What should be provided to manually disconnect the control circuit?
  • Foam plastic used as duct linings must conform to which section of the North Carolina Mechanical Code?
  • What is the required height above the floor for maintaining indoor temperature measurement?
  • What type of doors can allow return air to travel through the living space?
  • Which of the following is the minimum required clearances for duct systems?
  • According to the mechanical code, which type of temperature should the gypsum board surface be maintained above?
  • Manufacturer's installation instructions should be available on the job site at the time of what?
  • What pressure and duration is required for pressure testing an assembled loop system before backfilling?
  • Liquid single-phase solar energy systems must be equipped with what type of tank?
  • What is the appropriate installation method for systems to prevent flooding concerning condensate drains?
  • Nonmetallic mechanical fasteners for dryer ducts must be listed to which standard?
  • What is required to protect the exterior of piping from corrosion?
  • In compliance with Section 306.5, when is access to mechanical equipment on roofs or elevated structures not required?
  • What must be done to ductwork when adding cooling equipment to existing ductwork in an attic?
  • In dwellings with 1,600 square feet or less, is a central return permitted?
  • What is a requirement for servicing duct heaters?
  • For exhaust outlets conveying other products, what is the distance required from property lines?
  • Piping located in a flood hazard area must be designed to withstand what?
  • Makeup air in a commercial kitchen must be approximately equal to what?
  • Where must motors for fans that convey flammable vapors or dusts be located?
  • In multi-level structures, how many separate returns must be installed on each level?
  • What is not recommended when making alterations to engineered wood products?
  • What is permitted in corridors as a source of makeup air for exhaust systems in specific rooms?
  • When designing encounter points for maintenance, what is essential for a fan's motor?
  • Which type of system must be approved if used in the corridor return air system?
  • What is the purpose of cleanouts in grease ducts according to the North Carolina Mechanical Code?
  • According to the code, how should air supplies be adjusted?
  • Penetrations by air ducts of any floor or ceiling assembly must be protected by what?
  • Pumps shall be listed and labeled in accordance with __ __.
  • What is the purpose of legible identification on duct insulation?
  • Which kitchen exhaust systems are specified to be prohibited from energy recovery ventilation systems?
  • What describes equipment, materials, or products with a label from a recognized testing laboratory?
  • Which type of tank is required to be installed in every hot water system?
  • What is the primary function of a backdraft damper in ductwork?
  • What is the relationship between makeup air and exhaust air in a commercial kitchen?
  • What is the minimum cross-sectional area required for an areaway when the duct termination is below 12 inches above finished grade?
  • What type of fittings should be avoided in fuel oil piping?
  • Which type of fuel oil tank is exempt from certain supply piping regulations?
  • How must the equipment and installation be positioned relative to the flood level rim of the condensate drain pan?
  • What is the implication of a duct terminating above the roof surface without meeting height requirements?
  • Which venting system type operates under positive static pressure to remove flue gases?
  • What code must the design and construction of the machinery room adhere to?
  • Openings in machinery rooms are permitted when ducts and air handlers operate at pressures lower than the room and are _____.
  • What must be the minimum clearance for a grease duct to noncombustible construction?
  • Which refrigerant liquid line group requires Schedule 80 carbon steel pipe in smaller sizes?
  • What is typically necessary for access to installations requiring maintenance?
  • What size must openings in screens and louvers be at minimum?
  • Where must high pressure steam safety valves be vented?
  • Systems using positive-displacement compressors containing more than how many pounds of refrigerant must have stop valves?
  • Which standard requires that air distribution systems be equipped with smoke detectors?
  • What is the minimum height from finished grade for a chimney termination?
  • Where should shutoff valves be installed in relation to a building?
  • Which code is specifically for oil and solid fuels?
  • Electric boilers must be listed and labeled according to which standard?
  • Which joint involves no melting of the materials, merely using a chemical bond in thermoplastic piping?
  • Is locking access port caps a requirement in North Carolina?
  • Where should connectors be located in relation to the appliance?
  • What should be attached to the boiler along with the manufacturer's rating data?
  • Which item does steam piping need to be able to drain?
  • Proper allowance shall be made for _____, contraction, jarring and vibration.
  • Which type of liquid or gas must not be used as a heat transfer fluid?
  • Which type of vent must all fuel-burning appliances discharge their combustion products to?
  • What is the minimum thickness of metal required for the construction of exhaust ducts?
  • What should be considered when constructing ductwork according to SMACNA standards?
  • What must ducted heat recovery ventilators comply with?
  • What is the required width for passageways around boilers?
  • What is the required outdoor air rate for corridors and common areas within conditioned spaces?
  • What aspect does a duct NOT include in its definition?
  • In what type of installation must domestic range hoods discharge outdoors?
  • What type of return is sufficient for air movement in small houses with limited conditioned area?
  • In ground-source heat pump loop systems, reused materials are not permitted to be what?
  • The installation of dryer exhaust ducts for Type 2 clothes dryers must comply with what?
  • What type of valves must be provided for tempering water supplied to the potable hot water system?
  • What is the maximum allowable pressure for a low-pressure boiler utilizing water?
  • What is prohibited in clothes dryer exhaust ducts to ensure proper exhaust flow?
  • What is the primary purpose of an exhaust system in industrial areas?
  • Which of the following devices captures grease and moisture before they reach the duct system in a kitchen?
  • What must be equipped on dryer exhaust ducts as a safety feature?
  • Type II hoods are installed for appliances producing which byproducts?
  • How should the permanent warning notice be attached to the sauna room?
  • What is the appropriate description for the material used for duct construction that does not need sealant?
  • What is the maximum design temperature allowed for air to be conveyed in flexible air ducts?
  • Air transferred from occupiable spaces is not prohibited from serving as _____ ___ for required exhaust systems in spaces like kitchens and baths.
  • What are the minimum dimensions for a working space required in front of the control side to service an appliance?
  • If the depth of the passageway exceeds a certain threshold, what materials must line the walls?
  • Commercial cooking appliances that require a Type I hood must also have what type of system installed?
  • Which joint would likely require the highest temperature to produce?
  • What is the minimum pitch of rise required when installing a connector?
  • What must be done to all pipe or tubing after cutting?
  • Hydronic piping systems must be tested hydrostatically at how many times the maximum system design pressure?
  • In a forced draft system, what design feature is crucial for maintaining safety during operation?
  • Which type of thermal storage units must also be listed and labeled under the code?
  • Which type of dampers should not be installed in combustion air ducts?
  • Which type of dampers should be used in HVAC systems during a fire?
  • Factory-built chimneys for solid fuel-burning appliances must comply with the Type HT requirements of UL 103 and be marked "__________".
  • What is a key characteristic of a closed-loop system in HVAC?
  • Which type of appliance would require a special designation marking on the associated chimney?
  • Does unconditioned basement ductwork require insulation with the addition of cooling?
  • What is the maximum spacing allowed between permanent fall arrest systems on the roof?
  • Which system's standards do supply tanks need to meet for UL certification?
  • Which of the following would NOT typically fall under the category of prohibited systems for energy recovery ventilation?
  • The relief valve in a reduced pressure system must be set at what level of pressure according to system design?
  • Which of the following is NOT a way makeup air must be provided?
  • What size of stop valves must be securely mounted independent of tubing or supports when used with soft annealed copper tubing or hard-drawn copper tubing?
  • Which type of pipe should not be used for connectors passing through an unheated space?
  • Energy recovery ventilation systems installations are not permitted in which type of dryer exhaust systems?
  • What is a requirement for floor registers regarding concentrated loads?
  • Air distribution systems must be equipped with smoke detectors that are _____ and labeled.
  • What is the maximum area of tenant space where corridors can be used for conveying return air?
  • Which piping material is NOT mentioned as being approved for use in heating panels?
  • What type of kitchen exhaust systems are included in the prohibited applications for energy recovery ventilation systems?
  • How far must the termination of chimney or vents equipped with power exhausters be from the lot line or adjacent buildings?
  • Which type of space has no permanent connections to other spaces?
  • How many types of auxiliary drain systems are mentioned as necessary for protection?
  • At what maximum interval must clothes dryer exhaust ducts be supported?
  • How many stories must a return air riser serve to require smoke detectors on each story?
  • What is the minimum clearance required for Type I hoods to combustibles?
  • What is the consequence for insufficient clearance of grease ducts to combustibles?
  • What function does a water level detection device provide if the primary drain is blocked?
  • What feature must each volume damper used in air supply adjustment have?
  • In which scenario does most refrigerant release occur in an indirect closed system?
  • What is the minimum thickness for nonmetallic pans?
  • What type of system would be characterized by the use of positive static pressure to expel gases?
  • Type II hoods must be constructed of what minimum gauge stainless steel?
  • What is the function of low-water cutoff controls as per safety standards?
  • Which vent type is used with oil-burning appliances listed for Type L vents?
  • What method must be used to join copper tubing according to the relevant code section?
  • What is NOT a method of protecting duct systems that penetrate non-fire rated floor assemblies?
  • In energy recovery ventilation systems, what type of heat is allowed to be recovered according to the exception?
  • What is the minimum height above grade for ducts conveying explosive or flammable vapors?
  • In a calculation to determine face velocity, what do you divide the CFM by to find the result?
  • What is the purpose of tie straps in ductwork?
  • What is the minimum distance of a ventilation air intake from a lot line?
  • Flexible air connectors are prohibited from passing through which of the following?
  • Which section mentions that the commercial cooking appliances must have a specific installation?
  • What is the minimum damper rating for penetrations of less than 3-hour fire-resistance-rated assemblies?
  • What type of fireplace door should not be installed unless specified testing and labeling have occurred?
  • What must hydronic piping systems be designed and installed to allow?
  • What must happen to the liquid combustion byproducts from condensing appliances?
  • When does a relief valve discharge fuel oil according to pressure limitations?
  • Which term refers to appliances and materials included in a list published by an acceptable organization?
  • Welding on pressure vessels must be performed by which type of holder?
  • Which closure system marking indicates the use of pressure-sensitive tape according to UL 181A?
  • What is the minimum continuous exhaust rate for a bathroom fan in R2 occupancy?
  • What is the minimum distance from the lot line or adjacent buildings for chimney or vent terminations equipped with power exhausters?
  • What is the minimum clearance to combustible materials for a hydronic piping system when the exterior temperature exceeds 250°F?
  • Duct heaters located within how many feet of a heat pump or air conditioner need to be listed and labeled?
  • What is referred to as the written, graphic, and pictorial documents used for obtaining a building permit?
  • What is the minimum flash point for liquid adhesive coatings used on filters?
  • What is the minimum distance that a drapery or similar combustible object must be from a floor furnace register?
  • What should not be necessary during maintenance of drain lines?
  • Where should cooking appliances not be installed?
  • Where should condensate not be allowed to discharge to prevent a nuisance?
  • What is the minimum height of the appliance service space when located under floors?
  • What is the applicable standard for oil-burning stoves?
  • Electric furnaces must be tested in accordance with which standard?
  • What type of joint is created between pipes or fittings that is not welded, brazed, caulked, soldered, or heat fused?
  • For a connection of a parking garage to a fuel fired appliance room, what alternative setup can be used if specific conditions are met?
  • How far must the fall arrest anchorage connector devices be placed from the roof edges?
  • What is the minimum width of metal straps used for supporting ducts in one-and two-family dwellings?
  • What type of construction is required for separating boiler rooms from other rooms in public schools?
  • What must permanently identify each subslab soil exhaust duct within the floor level?
  • In which type of kitchen ventilation system is the air balance critical that must include a schedule or diagram?
  • Listed and labeled hearth extensions should comply with which standard?
  • What is the minimum distance a floor furnace must be placed from the nearest wall?
  • To prevent exceeding design limitations, what is essential for solar energy system components that contain pressurized fluids?
  • What should ventilation air not be?
  • What type of dampers should be provided at the locations specified in the mechanical code?
  • What is required for roof and wall penetrations to prevent the entry of water, rodents, and insects?
  • Are undercut doors allowed for return air movement?
  • All environmental air exhaust outlets must be at least how far from property lines?
  • What characteristic should ducts possess to ensure effective airflow over filters?
  • Which term refers to a single unit providing complete, independent living facilities for individuals or groups?
  • What must be done if the condensate drain lines are blocked?
  • In areas prone to flooding, tanks must be installed at or above what level?
  • How long can flexible air connectors be limited in length?
  • What is the purpose of not allowing valves on return piping?
  • Which UL standard must dampers comply with according to the code?
  • What type of appliances can be installed in storage closets according to prohibited locations?
  • What is the minimum thickness of 16-inch duct made of aluminum in a residential system?
  • What type of equipment must be pressure tested according to the Mechanical Code?
  • Appliances located out of a vehicle's normal travel path are exempt from what requirement?
  • What must ducts that penetrate non-fire-resistance rated floor assemblies be protected by?
  • What type of collectors must be listed and labeled according to the specifications?
  • Which aspect of vent piping is important for safety?
  • What should return piping connect to on a fuel oil tank?
  • What is the term for a diffuser system that conveys and diffuses air into a space under positive pressure?
  • Which of the following describes a room that typically contains a bathtub or shower?
  • What type of supports are recommended for equipment near condensate drain pans?
  • What type of information must a ground source heat pump loop system indicate where it enters a building?
  • Which of the following statements is true regarding the maintenance of solar energy appliances?
  • When testing refrigerant systems, the test pressure should be at least what in relation to the design pressure?
  • What is required where a grease duct serving a Type I hood penetrates a ceiling?
  • What is the maximum height for the bottom of an air inlet or exhaust opening in fuel dispensing areas?
  • What can be found in direct and indirect open-spray systems?
  • What type of dampers are required for dryer exhaust ducts?
  • What standard must oil-fired pool and spa heaters comply with?
  • What generally constitutes the role of a code official?
  • What is a crucial feature that must be present at the termination of dryer exhaust ducts?
  • What happens to a fire damper after heat is detected?
  • What is a defining feature of low-heat appliances?
  • The cross-sectional area of a flue serving a solid-fuel-burning appliance shall be not greater than __________ the cross-sectional area of the appliance flue collar or flue outlet.
  • Type L vents shall terminate not less than _________ above the highest point of the roof penetration.
  • To avoid damaging consequences, how should refrigerant piping in concrete floors be treated?
  • What feature must the manual disconnecting means have?
  • Microwave cooking appliances must be in accordance with which standard?
  • What causes the natural draft in a chimney or vent system?
  • Which dry cleaning system category is related to solvents with a flash point at or above 140ºF?
  • For refrigerant liquid lines, which material has a specified maximum size for use in certain groups?
  • What type of solar system component should be used to manage expansion and contraction of fluids?
  • Boilers must be mounted on floors of what type of construction unless otherwise listed?
  • Type I hoods used over solid burning cooking appliances must discharge to which type of exhaust systems?
  • What portion of supply air includes outdoor air and any recirculated air treated to maintain air quality?
  • When connecting to the flue collar, what is true about the connector's size?
  • How should duct connections to flanges of air distribution system equipment be treated?
  • What type of barrier must insulated exterior ducts be protected with?
  • What type of boilers operate at pressures exceeding 15 pounds per square inch?
  • What is the correct construction type for Type I hoods over heavy-duty appliances?
  • In the context of mechanical systems, who is considered the authorized agent of the owner?
  • The venting system that conveys any products of combustion from a dryer must be independent of what?
  • What is the passageway within a chimney or vent called where combustion gases pass?
  • What is the requirement for fire dampers and similar devices in clothes dryer exhaust ducts?
  • Which of the following could be a potential issue if door swing clearance is not maintained?
  • What is the minimum air velocity required in grease ducts serving Type I hoods?
  • Per ASME Boiler and Pressure Vessel Code, how should expansion tanks be constructed?
  • What is the minimum ambient temperature that heat transfer liquids must be protected from freezing?
  • Which category includes appliances such as electric and gas hot-top ranges and electric fryers?
  • All systems containing how many pounds or more of a refrigerant must have stop valves?
  • What type of control should be present for coil-type boilers requiring forced circulation?
  • What is an essential design feature for steam piping systems?
  • What type of air system is classified under indirect open spray systems?
  • Only __________ dampers and __________ dampers labeled for use in dynamic systems shall be installed in HVAC systems designed to operate with fans on during a fire.
  • What is the minimum clearance above the floor for appliances located in public parking garages?
  • According to NCMC, energy recovery ventilation systems cannot be applied to which of the following?
  • What is the requirement for the automatic fire suppression system in commercial cooking operations?
  • What is the required depth of grease duct reservoirs?
  • What is the term for an enclosed space intended for human activities, excluding storage areas?
  • What is the consequence of smoke generated in one space being transferred to another?
  • In which conditions can ducts that exhaust clothes dryers penetrate walls or ceilings?
  • What defines the Type IV dry cleaning systems?
  • A __________ shall be installed to prevent rain from entering the vent system.
  • What type of device is used to capture grease and contaminants before they enter a duct system?
  • Energy recovery ventilation systems are not allowed in which type of control system?
  • How many cubic feet per minute can panned joists accommodate for 10-inch joists that are 16 inches on center?
  • The required separation distance from contaminant sources for mechanical and gravity intakes is measured from which part of an area?
  • What is the maximum temperature for air conducted through flexible air ducts and connectors?
  • What is the maximum size for a collection receptacle on a grease hood?
  • Screen openings on an intake opening for a commercial building shall not be greater than ___ inch.
  • What type of kitchen hood is used for collecting steam, vapor, heat, and odors?
  • What is the minimum distance a fill pipe should be from a building opening?
  • Clothes dryer exhaust ducts should not extend into or through which areas?
  • What is the minimum distance a vent termination point should be from an interior corner formed by two walls?
  • How much above the floor should appliances installed in public garages be placed?
  • Which standard outlines the electrical safety requirements for refrigerant systems?
  • Packaged oil-fired boilers must meet the standards of which labeling?
  • What cannot be changed beyond the limit rating for an appliance?
  • Who is responsible for providing a complete control diagram and boiler operating instructions for each installation?
  • What is the maximum length permitted for transition ducts?
  • Individual smoke detectors shall not be required for any fan powered unit serving only __________.
  • How far must environmental air exhaust be from operable openings into buildings for all occupancies other than Group U?
  • What is the requirement for joints in refrigerant piping installed in the field?
  • How shall steel pipe joints embedded in a building be joined?
  • What distinguishes a modular boiler from other boiler systems?
  • What is the minimum clearance to combustibles for a Type I hood?
  • What is the minimum ventilation airflow rate that systems must be capable of producing per square foot?
  • Which device is specifically used to restrict the passage of flame in ducts and air transfer openings?
  • What position should the disconnecting means be capable of being locked into?
  • A hydronic piping system should not be in what type of contact with building materials?
  • What is the minimum distance in feet that intake openings must be located below contaminants located within 10 feet?
  • Which type of cooling equipment is exempt from certain code requirements?
  • What should be ensured about the pressure relief valve's placement in a hydronic system?
  • What type of assembly should flexible ducts and air connectors not pass through?
  • Which type of hoods is suitable for appliances that do not generate grease or smoke?
  • A gas-tight joint formed with alloys melting above 1,000ºF is known as what?
  • What is the minimum damper rating required for penetrations of 3-hour or greater fire-resistance-rated assemblies?
  • During concrete pouring, the pipe must be maintained at what condition?
  • What must be done to the air inlet of a vented wall furnace to ensure safety?
  • What must separate the corridor from a return air plenum?
  • Household electric ranges should be listed and labeled according to which standard?
  • Rooms containing refrigeration machinery shall be _____ and _____ in accordance with IBC and IMC.
  • For visual inspection, what should be kept open in refrigerant piping?
  • What type of joint is characterized by the joining of metal parts with metallic mixtures of alloys melting below 1,000ºF?
  • What is the minimum distance a grease duct must have from combustible construction?
  • What is a necessary venting requirement for gas appliances?
  • How far should the noncombustible material extend around the hood?
  • What must liquid single-phase solar energy systems be equipped with according to the code?
  • Where should a pressure relief valve be installed in a hydronic piping system with reduced pressure?
  • Which code must detached one- and two-family dwellings comply with?
  • What is the objective of space-heating systems in interior spaces intended for human occupancy?
  • What is the minimum required opening dimension for cleanouts serving horizontal sections of grease ducts?
  • What is the maximum pressure tolerance for joints in a refrigeration system located in an air duct?
  • According to the code, vent terminals for direct-vent appliances must be installed following which guidelines?
  • What should be used to permanently identify access points for fire dampers?
  • Factory-built chimneys for medium-heat appliances must comply with UL 959 if flue gases exceed __________.
  • What provision must be made for solar energy equipment and appliances?
  • What is the maximum allowable pressure for tests that require gauge increments of 0.1 psi or less?
  • Where should the midpoint of the water-gauge glass be positioned?
  • Which component must be labeled for use with a specific factory-built chimney system?
  • Which type of venting is allowed for appliances where ducts penetrate ceiling membranes?
  • An air washer system is typically found in which type of facility?
  • What size must the ventilation opening in sauna rooms be located near the top of the door?
  • What characteristic defines an indirect vented closed system?
  • Which gauge stainless steel is the minimum for Type I materials?
  • What is the minimum damper rating required for 3-hour fire-resistance-rated assemblies?
  • Where should a manual shutoff valve be installed in relation to all controls?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy